Home > Troubleshooting > Electrical Problems > Mercedes EZS EIS Ignition Switch Problem, Cause, Solution

Mercedes EZS EIS Ignition Switch Problem, Cause, Solution

Last updated:

In this guide (6 sections)
  1. Possible Symptoms
  2. Common causes
  3. How to Fix Mercedes Ignition Switch Problems
  4. Your three options when the EIS has failed
  5. What scanner do I need to diagnose this?
  6. Related guides

Mercedes-Benz owners may face a problem when the key no longer turns in the ignition. This issue is often caused by a defective key, a bad shifter module, a failed Electronic Ignition Switch (EIS), the EIS-EZS, or a bad steering lock module (ESL). This problem can affect various Mercedes-Benz models, including the E-Class, S-Class, C-Class, CLK-Class, ML-Class, and SL-Class.

Watch: Mercedes-Benz Electronic Ignition Switch EIS Failure

Possible Symptoms

Possible symptoms of a failed EIS or EZS ignition module include:

  • The key does not turn in the ignition due to a failed EIS
  • The key doesn’t turn during cold weather
  • The key may turn, but the instrument cluster lights don’t turn on
  • Unable To Turn The Key, Unable To Start The Car
  • I can turn the key, but the car won’t start
  • The key works intermittently
  • The push start button no longer works

Common causes

The Mercedes-Benz ignition switch, often called the immobilizer module, can fail on its own, and in some cases the failure is triggered by something the owner did. For example, some common reasons why the ignition module failed are:

  • Low battery voltage
  • A voltage spike or power surge
  • Connecting jump-starting cables while the key is in the ignition.

During any of the above scenarios, the EIS-EZS may lose its memory. While it can be diagnosed with a Star Diagnostic Scanner used at dealerships, it can’t be repaired with this scanner. Mercedes dealers don’t repair a bad EIS-EZS module. They will recommend that the module be replaced. That’s not necessarily the only solution; see alternatives below.

How to Fix Mercedes Ignition Switch Problems

Step 1

MERCEDES EZS EIS IGNITION SWITCH, KEY , ELV , FBS3 REPAIR SERVICEA defective key can very well cause these symptoms.  If you have a spare key, try to see if you are experiencing the same symptoms with the other key. If the other key works, keep using it for a couple of weeks to verify that the issue is the key and not the EIS.

Step 2

Try scanning your Mercedes-Benz for fault codes. You need a scanner that reads the EIS, ESL and immobilizer modules, not just the engine. A YOUCANIC scanner or a dealer Star Diagnostic unit will both do this. The only issue here is that if you can’t turn on the ignition, you can’t power on the OBD-II port and the scanner. If the ignition turns intermittently, consider yourself lucky and scan for codes. Hopefully, there are fault codes that will point you to the problem. Mercedes EIS EZS ignition switch module

Step 3

Mercedes EIS EZS ignition switch moduleDiagnosing Mercedes ignition problems isn’t a simple DIY job. You may consider taking your car to the dealer or an independent shop and having them troubleshoot the problem. If they conclude that the Ignition Switch (EIS-EZS) is the culprit, you will be told that the switch must be replaced. This is an expensive repair that can cost several hundred dollars. You have a few options here. Have the dealer install a new ignition switch, and they will program it to match the VIN of your Mercedes-Benz. Many owners install an ignition switch, ECU, shifter module, and other parts from a donor vehicle. You can’t replace the ignition switch only with one from a used Mercedes-Benz. Several parts must be swapped because the stored VIN needs to be the same.

There is also a third option, which may be the cheapest way to fix the Mercedes ignition switch module. Some companies can repair Mercedes-Benz ignition modules. You will need to remove the ignition module from your Mercedes-Benz and ship it to one of these companies that can test and repair the EIS-EZS. Once the module is repaired, it is returned to you. Besides being a lot cheaper than installing a new ignition module, it also doesn’t require any programming or coding. The VIN stored in the Ignition Module (EIS-EZS) matches that of the car; it’s your old module, after all. Just install it, and you are ready to go.

Your three options when the EIS has failed

Option Programming needed Keep your existing keys Relative cost
New module from the dealer Yes, coded to your VIN Usually no, keys are rewritten Highest
Used module from a donor car Yes, and you must swap EIS, ECU and shifter module together so the stored VIN matches No Medium, plus a lot of labor
Repair or clone your original None Yes Lowest
Why repair avoids the programming step entirelyYour EIS already stores your car’s VIN. Repair it, or clone its data onto a tested replacement, and the module the car gets back is still the one it expects. No coding, no dealer visit, and your existing keys keep working. That is the whole reason this route costs a fraction of the alternatives.

Where to send it

Module Medics offers a mail in Mercedes EIS and EZS ignition repair and cloning service. You remove the module, ship it, and it comes back tested and ready to install. They also handle ESL steering lock modules, key programming including FBS3 systems and ECU repair.

Covered chassis include W202, W203, W208, W209, W210, W211, W215, W219, W220, W230, W463, W639 and W906, across the A, B, C, E, G, S, SL, ML, GL and SLK classes.

Before you condemn the EISTry your spare key first. Keys fail more often than EIS modules do, and a key costs far less to replace. If the spare works normally for a couple of weeks, the module was never the problem.

What scanner do I need to diagnose this?

There is a catch specific to this fault. If the ignition will not turn at all, the OBD port may have no power, and no scanner of any brand can talk to the car. If the key turns intermittently, scan it while it is working.

When you can get power, the YOUCANIC scanner reads the EIS, ESL, shifter module and immobilizer, which is where these faults are stored. A basic code reader sees none of them.

We sell the YOUCANIC scanner. The function comparisons below come from each manufacturer’s own documentation so you can check them yourself.

Compared to Xentry

Xentry diagnoses the EIS, and so does the YOUCANIC scanner. Neither one repairs a failed EIS. Mercedes dealers do not repair these modules at all, they replace them, which is exactly why the repair and clone route exists. Xentry’s exclusive function is online VIN coding, which you need for a new module and do not need for a repaired one.

Confirm it is the EIS and not the key

Read the EIS, ESL and immobilizer modules before committing to a repair that costs hundreds.

See the YOUCANIC scanner

Next step

Run a full system scan on your Mercedes-Benz

Before you buy parts, scan every control module, not just the engine. It shows the root fault behind the warning lights and tells you whether the problem is still active. See how to do a full health check.

3 comments

  1. Sharing in case it helps another Sprinter owner. Our 2018 Sprinter W906 motorhome had intermittent no start problems since new, at least two days a week, and no Mercedes workshop could find the cause without replacing parts. Then, 900 km from home, the key would not turn at all, and the spare key would not turn the ignition on either. Roadside assistance took two hours to find that the ESL (electronic steering lock) actuator had failed. No new ESL unit was available for four weeks, so the dealer installed an emulator to get us home. If your Sprinter has random no starts and the key sometimes will not turn, have the ESL checked early.

  2. Goodmorning, I tried to jump start my type 220 Sclass with the key in the ignition and now the key will no longer turn. What do you think has been damaged?
    Kind regards Garth

  3. I got a problem with the ignition key it doesn’t start the car, my Benz C 180 203

Leave a Reply

Your email address will not be published. Required fields are marked *